Author Topic: Accuracy  (Read 2838 times)

Offline axisofoil

  • Trade Count: (0)
  • Colonel
  • *****
  • Posts: 1284
    • View Profile
Re: Accuracy
« Reply #30 on: May 14, 2010, 09:43:05 PM »
Quote from: "Whiskey11"
Quote from: "axisofoil"
my barrels don't so much as put any gray onto a cleaning patch when I clean my barrels. My AK usually gets about 1000 rounds between cleanings, while my SR16 gets about 400 rounds between cleanings.

1000 rounds?  400 rounds?  Whiskey Tango Foxtrot?  I understand it's Arizona, and sand gets everywhere, but 1000 rounds?  400 ROUNDS?  Really?  Anal much?  I went 50,000 rounds before cleaning any of my AEG's in my breif stint in AZ and they where not that dirty...  Less than 15000 rounds and I worry about your hop up bucking wearing out prematurely from having a cleaning rod jammed down it that often.  I take it you dont go through very many rounds in a game then?

Correct on all points. And remember... up here in Northern AZ... there's not nearly as much dust. :D

I'm anal about my barrels/buckings/nubs (and YES, nubs DO wear out... just takes a loooong time, approximately 1500 cleaning intervals :P.  Less time for h nubs though)

I don't generally go through more than that many rounds in a day in either gun.

For the SR (400rds), I remove the barrel/hopup/bucking to clean that. Just clean the barrel by itself, only clean the bucking if it needs cleaning.
The AK... well... I'm sure the bucking will wear out eventually. I'll let you know. It's still a baby. Under 10k rounds total so far... gun bucking and barrel are included in that.

I might also add that it's just the externals/barrels that get cleaned that often. It's usually at least 5 or 6 of those cycles before I open a gearbox to clean. Better to be clean than crunchy!
« Last Edit: December 31, 1969, 05:00:00 PM by Guest »

Offline Whiskey11

  • Trade Count: (0)
  • Sergeant Major
  • *****
  • Posts: 522
    • View Profile
Re: Accuracy
« Reply #31 on: May 16, 2010, 06:38:43 PM »
Wow...  thats just a bit much... I can't imagine the guns lasting terribly long like that, but thats not my problem ;)
« Last Edit: December 31, 1969, 05:00:00 PM by Guest »

Offline axisofoil

  • Trade Count: (0)
  • Colonel
  • *****
  • Posts: 1284
    • View Profile
Re: Accuracy
« Reply #32 on: May 16, 2010, 08:54:53 PM »
Quote from: "Whiskey11"
Wow...  thats just a bit much... I can't imagine the guns lasting terribly long like that, but thats not my problem ;)

So far... I've only worn through 1 bucking (systema... and it wasn't sealed to the barrel properly)... And 1 tappet plate return spring (I don't know exactly how that happens... but it did).

I don't see why they wouldn't last. I'm careful and mindful during assembly and disassembly. I just like to keep my gear clean.

If it makes you feel better... I have never cleaned my trishot. lol. Granted, I've only used it once.


Anyways... aside from my OCD'edness, good airseal, hopup, hopup bucking, nub, and tightbore (volume matched to a cylinder, of course) is your best bet for accuracy. A little magic and selling your soul to Satan, or perhaps being in the favor of a higher being would help out some too.
« Last Edit: December 31, 1969, 05:00:00 PM by Guest »

Offline Rako

  • Trade Count: (0)
  • Sergeant
  • *****
  • Posts: 125
    • View Profile
Re: Accuracy
« Reply #33 on: May 16, 2010, 08:57:38 PM »
Quote from: "axisofoil"
A little magic and selling your soul to Satan, or perhaps being in the favor of a higher being would help out some too.
Ah, good point.  Ill have to look into that.
« Last Edit: December 31, 1969, 05:00:00 PM by Guest »
"Life is tough. Life is even tougher if you're stupid." - John Wayne