« previous next »
Pages: [1]

Author Topic: I found my Problem  (Read 1273 times)

Offline kingsix123

  • Trade Count: (0)
  • Sergeant
  • *****
  • Posts: 144
    • View Profile
    • http://www.freewebs.com/kingsixone
I found my Problem
« on: September 21, 2005, 09:51:27 PM »
For all those who were are the JoMax game, i had been having trouble with my Fuses blowing on my TM MP5. Well i remmemberd that i purchased a 30 AMP High Discharge rate 8.4v 11 Mah battery! I'm still curious though, what advantage does this battery have if it blows fuses? is it designed for a larger motor? Thanks,
         [smilie=armata_pdt_36.gif] Lock N Load Gentleman

                      Tim
« Last Edit: December 31, 1969, 05:00:00 PM by kingsix123 »
Logged
The only thing Necessary  for the triumph of evil is for good men to do NOTHING!


Offline busta_cap

  • Trade Count: (0)
  • Lieutenant General
  • *****
  • Posts: 3887
    • View Profile
(No subject)
« Reply #1 on: September 21, 2005, 10:13:34 PM »
More amperage means more discharge...you basicly get more flowing at a time and less "wearing down". You will drain your battery faster but you get more juice so you will be able to turn over harder springs faster than with the same battery with a lower discharge rating.
« Last Edit: December 31, 1969, 05:00:00 PM by busta_cap »
Logged

Offline kingsix123

  • Trade Count: (0)
  • Sergeant
  • *****
  • Posts: 144
    • View Profile
    • http://www.freewebs.com/kingsixone
(No subject)
« Reply #2 on: September 21, 2005, 10:24:42 PM »
So using it won't burn up my motor? or do i need to put a heavier spring in before using this battery, because it was blowith my 1 amp fuses like they were threads!
« Last Edit: December 31, 1969, 05:00:00 PM by kingsix123 »
Logged
The only thing Necessary  for the triumph of evil is for good men to do NOTHING!


Offline Cheeze_IZ_G00d

  • Trade Count: (0)
  • Second Lieutenant
  • *****
  • Posts: 795
    • View Profile
(No subject)
« Reply #3 on: September 22, 2005, 05:28:03 PM »
Just dump the fuse all together. It is completely useless, snap the two connections where you put the fuse together and get some electrical tape.
« Last Edit: December 31, 1969, 05:00:00 PM by Cheeze_IZ_G00d »
Logged
Visit my website -
http://www.iwantafreedollarnow.com!!!

Get great ringtones here!

Offline Surplus man

  • Trade Count: (0)
  • First Sergeant
  • *****
  • Posts: 454
    • View Profile
(No subject)
« Reply #4 on: September 23, 2005, 12:12:48 PM »
id get a stronger spring so the power out put wasnt too much for the gear box, a stronger spring would even things out.
« Last Edit: December 31, 1969, 05:00:00 PM by Surplus man »
Logged
I saw this plug was in my wall here and then i noticed that your house was glowin like THE FRICKIN SUN! So, i uh put 2 and 2 together here and decided that your pissin me off...

-carl

Offline kingsix123

  • Trade Count: (0)
  • Sergeant
  • *****
  • Posts: 144
    • View Profile
    • http://www.freewebs.com/kingsixone
Upgraded
« Reply #5 on: September 23, 2005, 06:56:03 PM »
This is what i have done to it allready

PDI 150% Spring
Systema Aluminum Piston Head
Systema Reinforced Air Seal Nozzle
Systema Metal Bushings Set

What spring should i put into it to conpensate for the torque? Putting a harder spring should make it shoot harder too right? thanks,
             Tim

            [smilie=armata_pdt_36.gif] Lock n Load Gentleman!
« Last Edit: December 31, 1969, 05:00:00 PM by kingsix123 »
Logged
The only thing Necessary  for the triumph of evil is for good men to do NOTHING!


Offline busta_cap

  • Trade Count: (0)
  • Lieutenant General
  • *****
  • Posts: 3887
    • View Profile
(No subject)
« Reply #6 on: September 23, 2005, 07:18:48 PM »
THat is enough. Leave it there...the discharge rate just helps turn it over faster after the first time.. You will be fine.
« Last Edit: December 31, 1969, 05:00:00 PM by busta_cap »
Logged

Offline kingsix123

  • Trade Count: (0)
  • Sergeant
  • *****
  • Posts: 144
    • View Profile
    • http://www.freewebs.com/kingsixone
upgrade
« Reply #7 on: September 23, 2005, 07:53:15 PM »
I was thinkin about crankin it up to just under 400 fps, is that possible without purchaseing flat gears and all that?
Thanks,
              Tim


 [smilie=armata_pdt_36.gif] Lock N Load Gentleman
« Last Edit: December 31, 1969, 05:00:00 PM by kingsix123 »
Logged
The only thing Necessary  for the triumph of evil is for good men to do NOTHING!


Offline busta_cap

  • Trade Count: (0)
  • Lieutenant General
  • *****
  • Posts: 3887
    • View Profile
(No subject)
« Reply #8 on: September 23, 2005, 08:01:48 PM »
It should be just under 400 with that spring, if not get a systema silent head set and definately a spring guide with a bearing
« Last Edit: December 31, 1969, 05:00:00 PM by busta_cap »
Logged

Offline kingsix123

  • Trade Count: (0)
  • Sergeant
  • *****
  • Posts: 144
    • View Profile
    • http://www.freewebs.com/kingsixone
mp5
« Reply #9 on: September 23, 2005, 10:52:54 PM »
Well it's shooting 350-359, but i want it as close to 400 as i can get it, so i should a a systema silent head and spring guide? just makin sure before i order the parts lol. Thanks,
               Tim
« Last Edit: December 31, 1969, 05:00:00 PM by kingsix123 »
Logged
The only thing Necessary  for the triumph of evil is for good men to do NOTHING!


Pages: [1]
« previous next »